GSM7224R, GSM7248R Firmware Version 7.1.1.7

Published Feb 28, 2008

New Features/Enhancements/Bug Fixes:

1. Fail to create static route with default preference via web GUI.
2. Port security increase of MAC addresses from 20 to 48 per port.
3. Web GUI does not allow deleting of the buffered logs.
4. Web will return “The page cannot be found” error when attempt to go to “Maintenance -> Troubleshooting” page.
5. Switch might crash while repeatedly configure and refresh thru HTTPS.
6. Console port might hang while downloading configuration file after reset to factory default.
7. SNTP: additional character shown for command 'clock timezone'
8. The 100Mbps SFP fiber module showed as 1000Mbps speed after "clear config"
9. Failed to assign MAC ACL to a lag interface.
10. Failed to assign IP ACL to a lag interface.
11. The path external-cost value in STP changed incorrectly when path cost is modified
12. Web page for port channel (LAG) contains check box to have all ports to be selected as LAG members.
13. Routing VLAN MAC wasn’t deleted when the routing VLAN was removed.
14. Some online help web pages has various errors (e.g. spelling error, title mismatches etc.)
    

Known Issues:

1. If the web session is in HTTPS mode, and HTTP mode is used to perform firmware download, then the download will fail.
   Workaround: Use TFTP to perform firmware download via HTTP session instead.
2. If the web session is in HTTPS mode, and TFTP mode is used to perform firmware download, then there may not be a download success message displayed at the end of the download.
   Workaround: Although there may not be a completion message, but the firmware is downloaded successfully. So just ignore the absent of the success message.

Upgrading

1. Using the button below, download the firmware file.

   6.20 MB

2. If you have not setup any special functions on the existing switch other than the management IP address, or you have saved a copy of the configuration in a text file, proceed to the next step.
   • On the existing switch, use capture mode in Hyperterminal to capture the output from the switch console to a file.
   • On the switch console, type “show run”. The output of current running configuration will be captured in the file.
   • Open the file and review the content. If there is any changes to the configuration but not present in the file, manually add them. Save the file after it is done.
   Note: If you’re running Microsoft Vista and there is no Hyper Terminal communication program for serial port, then you might consider downloading a public program called Tera Term in this web site (http://hp.vector.co.jp/authors/VA002416/teraterm.html).
3. Start a tftp server on the PC where the new images are stored. If you do not have a tftp server, you may want to try either of the following public domain tftp servers:
   PumpKIN - http://kin.klever.net/pumpkin/
   Solarwind - http://support.solarwinds.net/updates/New-customerFree.cfm
4. On the switch console, type the following command:
• # copy tftp://<tftp server IP address><image name> system:image
• It will ask for confirm with input data displayed. Hit enter if all parameters look correct.
• The download should take a minute or two, after that, the code will be checked for possible corruption, if not, it will report firmware successfully upgraded.
• Reboot the switch by typing “reload” command or power cycle the switch.
5. After the switch is restarted, type the following command to verify the version is correct.
• # show hardware
6. .If you did not skip step #1, now you can use the saved “show run” output file to restore the switch to your configuration, otherwise skip this step.
• First enter exec mode, by enable command after you logged in.
• Once in exec mode, paste the content of that file to the console. If there is any error during such operation, please report it to NETGEAR tech support.
• Do a “show run” command on the console and make sure everything you expect to be there is present. If not, please report the problem to the tech support and manually add your configuration back.
7. You can now make additional configuration change for your application need. And be sure to use “copy” command to save the configuration after you’re done.

This product includes software code developed by third parties, including software code subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL Code and LGPL Code used in this product, are available to you at NETGEAR's Open Source Code Web page. The GPL Code and LGPL Code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more authors. For details, see the GPL Code and LGPL Code for this product and the terms of the GPL and LGPL.

d103260.asp